Epson WorkForce WF-7710 Setup Guidance

Epson WorkForce WF-7710 Setup

Step 1: Take out the Epson WorkForce 7710 printer from its package

  1. Open the box and remove the Epson WorkForce 7710 printer from it.
  2. Peel off the tapes from the printer.
  3. Raise the scanner lid at the top and remove the packing component on the scanner glass.
  4. Close the lid. Open the paper tray of the Epson WorkForce WF-7710 Setup.
  5. Check if the power cable, ink cartridges, printer software installation CD, manual, and French control panel stickers are provided in the carton.

Step 2: Power up the Epson WorkForce 7710 printer.

  1. Unpack the power cable given in the Epson WorkForce 7710 printer box.
  2. Connect an end of the cable to the power port of the printer and the other terminal to an electrical outlet directly.
  3. Lift the control panel. Configure the settings like the Language, Country, and Time on the panel.

Step 3: Insert the ink cartridges of the Epson printer.

  1. Raise the scanner unit and open the cover of the ink cartridge.
  2. Unpack the cartridges provided in the printer box and shake them.
  3. Remove the protective cover and tapes from the cartridges.
  4. Insert the cartridges into the respective slots of the Epson WorkForce 7710 printer.
  5. Close the access cover and scanner unit.

Step 4: Load enough sheets in the paper tray.

  1. Extend the paper cassette of the Epson WorkForce 7710 printer and take it out.
  2. Take a stack of suitable sheets and tap them on a flat surface.
  3. Fix the sheets by adjusting the paper guides.
  4. Insert the cassette into the Epson printer.
  5. Extend the output tray extension of the Epson WorkForce 7710 printer.
  6. Configure the paper settings on the control panel of the Epson WorkForce WF-7710 Setup.

Step 5: Set up the fax line.

  1. Take a phone cable. Connect the cable to the telephone wall jack and LINE port of the Epson WorkForce 7710 printer.
  2. Tap Proceed on the control panel of the printer to set up the fax line.
  3. To configure the fax setup later, tap Close.

Step 6: Launch the printer software.

  1. Make sure that the Epson WorkForce 7710 printer and computer are not connected.
  2. Computerize the software of the printer.
  3. Use the Driver Download buttons on this page to configure the software of the printer.
  4. You can also avail the software from the manufacturer’s site for free.

Epson WorkForce WF-7710 Driver Download Guidance

The software of the Epson WorkForce 7710 printer can be downloaded after setting up its hardware. Refer to the previous topic to configure the Epson WorkForce printer software.

Epson WorkForce WF-7710 Driver for Windows

Windows users can click the key below to avail the software of the Epson WorkForce 7710 printer.

Driver for Epson WorkForce WF-7710 Printer
  • The software suits the Windows operating system of any versions.
  • Driver file name: WF7710_Lite_NA.exe.
  • Driver file size: 11.4 MB.
  • Date of launch: 12th July in the year 2019.

Epson WorkForce WF-7710 Driver for Mac

If you are a Mac user, click the Driver Download button below to computerize the software of the Epson WorkForce 7710 printer.

Driver for Epson WorkForce WF-7710 Printer
  • The given software is compatible with any versions of the Mac operating system.
  • Driver file size: 13.7 MB.
  • Driver file name: WF7710_Lite_64_NA.dmg.
  • Date of release: 12th September in the year 2018.

Epson WorkForce 7710 User Manual Download

If you are finding guidelines to set up the Epson WF 7710 printer, use its manual. The manual has instructions to set up the hardware and software of the printer and execute its functions. It also has solutions to solve any problems that arise with the Epson WorkForce WF-7710 Setup.

Manual for Epson WorkForce WF-7710 Printer

Epson WorkForce WF-7710 Driver Installation

  1. Begin to install the software of the Epson WF-7710 printer once you download it. The step by step instruction to install the Epson printer software varies based on the OS version of your computer or laptop.
  2. Firstly, locate the driver file which you have downloaded on your computer.
  3. Double-click on the file to open it.
  4. Follow the instructions. Accept the Terms and Conditions.
  5. Set up the connection between your Epson WorkForce WF-7710 Setup and computer.
  6. Follow the prompts and carry on with the instructions on the screen to complete the installation process.
Epson WF-7710 Driver Installation

Epson WorkForce WF-7710 Scanner Driver Download

Epson WF-7710 Scanner Driver for Windows

Windows Scanner Driver for Epson WorkForce WF-7710 Printer

Epson WF-7710 Scanner Driver for Mac

Mac Epson WF-7710 Scanner Driver Download

Steps: Epson WF-7710 Wifi Setup

  1. Refer to the following steps to connect the Epson WF 7710 printer to your computer by using the Wi-Fi Direct mode.
  2. On the control panel of the Epson printer, tap the Home key to close if there are any messages on the screen if any.
  3. Locate the Wi-Fi icon and select it.
  4. Choose Wi-Fi Direct --> Start Setup --> Start Setup.
  5. Now a Network (SSID) name and password appear on the control panel of the Epson WorkForce WF-7710 Setup.
  6. Enable the wireless feature on your computer.
  7. Choose the SSID that appears on the control panel of the printer.
  8. Also, provide its passkey when your computer prompts.
  9. Wait until the printer gets connected to the computer.

How to Change Ink Cartridge on Epson WF-7710?

  1. Power up the Epson WF-7710 printer if it is turned off previously.
  2. Make sure that the Epson printer is in an active state and functioning properly.
  3. Raise the scanner unit at the top of the Epson WF-7710 printer.
  4. Open the cover of the ink cartridge.
  5. Squeeze the tab of the cartridge which you need to replace and remove it from the printer.
  6. Take the new cartridge which you have purchased to replace the old one.
  7. Remove the cartridge from its package and peel off the yellow-colored tape on it.
  8. Insert the cartridge into the correct slot of the Epson WF 7710 printer.
  9. Close the cartridge cover and gently press it to fix the cartridge.
  10. Close the scanner unit of the Epson WorkForce WF-7710 Setup.

How to Print 11x17 on Epson WF-7710?

  1. On the control panel of the Epson WF-7710 Printer, tap the home key.
  2. Choose Settings --> General Settings --> Printer Settings --> Paper Source Settings --> Paper Settings.
  3. Change the print settings like the Paper Size, Paper Type, and more. Make sure that you have configured correct paper size.
  4. Open the document which you desire to print on your computer.
  5. Locate the Print option and select it to configure the print settings.
  6. Tap Print to begin the printing process after configuring the print settings.

How to Print 13x19 on Epson WF-7710?

  1. Load print media in the input tray of the Epson WF 7710 printer.
  2. Open your document for printing on your computer.
  3. Click Print. Choose the name of your printer.
  4. Locate the Properties or Preferences option and select it.
  5. Set the paper size as 13x19.
  6. Configure the other print settings if needed.
  7. Finally, click Print to begin the printing process.

How to Print A3 on Epson WF-7710?

  1. Open your document you desire to print on your computer.
  2. Make sure that the Epson WF-7710 printer and computer are connected.
  3. On the display of your computer, go to the File menu.
  4. Locate the Print option and select it.
  5. Change the print settings if needed.
  6. Set the paper size as A3.
  7. After configuring the print settings, tap Print to begin the printing process.
  8. If you find it difficult to print A3 sheets, call our technical support team to avail easy guidance.

How to Scan on Epson WorkForce WF-7710 Setup?

  1. Make sure that the Epson WF 7710 printer software is installed on your computer.
  2. Connect the Epson printer and computer either by using the wired or wireless connection method.
  3. Keep your original document or ADF (Automatic Document Feeder) for scanning on the scanner glass of the Epson WF 7710 printer.
  4. On the printer’s control panel, tap the Home key.
  5. Locate the Scan option and select it.
  6. Choose any one of the options under Scan To.
  7. Follow the guidelines on the screen to execute the scan function of the Epson WorkForce WF-7710 printer.

How to Setup Scan to Email on Epson WF-7710?

  1. Make sure that the document for scanning is placed on the respective place of the Epson WorkForce 7710 Printer.
  2. Tap the Home key on the control panel of the printer.
  3. Click Scan. Select the Scan To option as Email.
  4. Make sure that the email server is configured previously.
  5. Carry on with the instructions on the display to execute the scan to email setup.
How to Scan to Email on Epson WF-7710

Epson WorkForce WF-7710 Setup Troubleshooting Guidance

Troubleshoot the problems with the Epson WorkForce WF 7710 printer by obtaining assistance from our techies. They are well-qualified to solve any issues that arise with the WorkForce WF 7710 printer. Refer to the following topics to fix the offline, not printing in black, and paper jam problems with the Epson printer.

Epson WF-7710 Offline Guidance

  1. The offline issue mainly occurs due to poor power connection.
  2. Disconnect the power cable of the Epson WorkForce WF 7710 printer.
  3. Wait for a few minutes.
  4. Check if the AC power cable is not damaged.
  5. Connect the cable to the power port of the Epson WorkForce WF 7710 printer and power supply directly.
  6. Do not use a surge protector for performing the power connection as it may cause power fluctuations.

Solved: Epson WF-7710 won't print black

  1. Open the scanner unit and cartridge access cover of the Epson WF 7710 printer.
  2. Remove the black ink cartridge from the printer.
  3. Check if the black cartridge is not damaged.
  4. Replace the cartridge with a new one if it is damaged.
  5. You can also replace the cartridge if its ink level is low.
  6. Make sure that you fix the cartridge into the correct slot of the Epson WorkForce WF-7710 Setup.

Epson WF-7710 Paper Jam Error

  1. Check for jammed sheets in the printer parts like the paper cassette and duplexer.
  2. Open the access cover of the Epson WorkForce WF 7710 printer.
  3. Check if there are any jammed sheets inside the printer and remove them.
  4. Close the access cover. You can use a flashlight to check for jammed sheets inside the Epson WorkForce WF-7710 Setup
  5. For more solutions to fix the paper jam error with the Epson printer, reach our well-qualified technical support team.
Epson WF-7710 Paper Jam Error
printer setup support