COMPLETE GUIDANCE FOR EPSON M2140 SETUP

  1. Unpack the printer and take out the accessories included in the printer box.
  2. Remove the printer cover from the front and remove the protective tapes surrounding the printer. Close the printer cover.
  3. Open the ink tank cover located on the right side.
  4. Remove the ink bottle cap and insert it into the ink filling port.
  5. You will see the ink level just below the filling port. Wait for it to fill fully and gently remove the ink bottle from the filling port. Close the ink bottle and the ink filling port.
  6. Take the power cord, plug it into the rear end of the printer, and connect the other end to the power source.
  7. Press the Power button to turn the printer on. Use the navigation buttons to set your preferred language.
  8. Now, lower down the paper cassette cover and pull out the paper cassette from the printer.
  9. Insert a stack of paper in the cassette and move the paper guides close to the edges of the paper.
EPSON M2140 SETUP
  1. Push the paper cassette into the printer and close the paper cassette cover.
  2. Configure the paper settings on the printer control panel.
  3. On your computer, install the Epson M2140 setup printer driver and connect the printer to the computer.

EPSON M2140 DRIVER FOR WINDOWS 10

Driver for  Printer

You can download the Epson M2140 driver from this page or the official Epson support page.

  1. Open the browser and enter the Epson URL in the address bar.
  2. Enter Epson M2140 in the search bar and press the Enter button.
  3. Click the Downloads tab and then select the Windows OS and its version from the operating system drop-down list.
  4. Click the Download button beside the recommended printer driver.
  5. Once the driver is downloaded to the computer, open the downloads section in the browser.
  6. Double-click the installer file to run the installation.
  7. The Epson installer page will now open.
  8. Accept the license agreement, select the software to be installed, and proceed with the instructions on the setup wizard.
  9. When you are prompted, choose the connection type and follow the on-screen instructions.
  10. The driver installation for the Epson M2140 setup printer will be completed.
EPSON M2140 DRIVER

EPSON M2140 DRIVER FOR MAC

Driver for  Printer

For your Mac computer, you can have the driver downloaded from the official Epson support page.

  1. Open the default browser and enter the URL of the Epson support page.
  2. Enter Epson M2140 in the search bar and press the Enter button.
  3. Just below the Drivers section, select the Mac OS option from the operating system drop-down menu.
  4. Click the Downloads tab and download the required driver.
  5. Once the driver is downloaded to the computer, perform a double-click on the installer file to run the installation.
  6. Choose the type of connection and follow the on-screen instructions.
  7. Once the driver is installed, the printer will be connected to the Mac computer.

EPSON M2140 MANUAL DOWNLOAD

User Manual for Lexmark X792de Setup

You can download the Epson printer manual from the official Epson support page.

  1. Open the default browser on your computer and go to the official Epson M2140 setup page.
  2. Click the Manuals and Warranty tab.
  3. Scroll down the list and choose your manual. Then click the PDF link near the manual.
  4. The Epson M2140 manual will be downloaded to your computer.

EPSON M2140 PRINT SETUP

  1. Load enough paper in the Epson printer paper cassette.
  2. Open a document on the connected computer.
  3. Click File > Print.
  4. Select your printer followed by Preferences or Properties.
  5. Make the required print settings.
  6. Click OK followed by Print.

EPSON M2140 VS M2170

  1. The main difference between Epson M2140 and Epson M2170 is that the Epson M2140 does not support the Wireless connection, whereas the Epson M2140 setup does.
  2. The other features are the same when it comes to comparison between both these printers.

EPSON M2140 MAINTENANCE BOX RESET

  1. Turn off the Epson M2140 printer.
  2. Press and hold the three navigation arrow buttons (left, down, and up).
  3. Press the Power switch/button to turn on the printer and then release the buttons.
  4. A new menu will appear on the Control Panel display. Use the arrow buttons to navigate to the option Clear Counters.
  5. Select the Maintenance Tank option and press the OK button.
  6. Power off the printer and again turn it on.
  7. The Maintenance tank will be reset.

EPSON M2140 INK REFILL

  1. On the printer control panel, select Maintenance > Reset Ink Level. Then press OK.
  2. Open the ink tank cover located on the right side.
  3. Take the new ink bottle, open the ink bottle cap, and insert the ink bottle into the ink filling port.
  4. You will see the ink level just below the filling port. Wait until the ink tank is filled.
  5. Remove the ink bottle from the ink filling port and close the ink tank.
  6. Finally, you have to press the Start button on the printer to reset the ink level.

EPSON M2140 SCAN SETUP

  1. To scan a document using the Epson M2140 printer, you have to install Epson Scan 2 and Epson Event Manager on your computer. You can download these scan utilities from the official Epson M2140 setup site.
  2. After installing the scan utilities on your computer, check whether it is connected to the printer.
  3. Open the document cover on the printer and load the document to be scanned on the scanner glass.
  4. Select the Scan option on the Control panel and use the navigation arrow buttons to choose the required scan option.
  5. Press the Scan button.
EPSON M2140 SCAN SETUP

EPSON M2140 TROUBLESHOOTING

There are some common issues that occur on all the printers. Similarly, when an error occurs on the printer, the relevant error message is displayed. Also, the animation or instructions to fix the error is also displayed on the printer. Moreover, on this page we have provided the instructions to solve the printer issues like printer offline, paper jam, and scanner error.

EPSON M2140 OFFLINE

  1. Initially, check whether the printer is powered up and connected to the computer.
  2. On the connected Windows computer, click the Windows icon at the bottom left corner of the desktop screen and select the Control Panel option.
  3. Click the Devices and Printers option from the Control Panel window.
  4. You will see the list of the printer(s) connected to the computer.
  5. Perform a right-click on the Epson M2140 setup printer and select the option See what's printing?.
  6. See if you have any pending print jobs and make sure to remove them from the list.
  7. Click the Printer option on the top left corner and see if you have enabled the option Use Printer Offline. If it is enabled, then deselect the option.

EPSON M2140 SCANNER ERROR

  1. Make sure the original document to be scanned is placed properly along the edges on the scanner glass.
  2. When the scan is not clear, make sure to make adjustments to the scan resolution to resolve the error.
  3. To reset the Epson Scan utility, open the Scan Utility on your Windows computer.
  4. Select the Other tab and then click the Reset button.
  5. The most common Scanner Error is the Error Code E-02. To resolve the error, all you have to do is to turn off the printer and then turn it back on.

EPSON M2140 PAPER JAM

Jammed paper Front Cover:

  1. Open the front cover of the Epson printer.
  2. Bring down the output switch lever.
  3. Remove the jammed paper and also remove the pieces of the paper from the slot.
  4. Once removed, raise the output switch lever and close the front cover.
  5.  

Jammed paper Inside printer:

  1. Cancel any pending print job.
  2. Lift the printer cover and remove the jammed paper.
  3. Close the Epson M2140 setup printer cover and follow the prompts on the LCD to remove the error messages.

Jammed paper Rear Cover:

  1. Remove the rear cover from the printer.
  2. If you find any fragments of paper or a jammed paper, remove it.
  3. Now, close the rear cover.
EPSON M2140 PAPER JAM
printer setup support