You will find the following accessories in the carton: Follow these below mentioned steps the Canon Pixma Ts6220 Setup.

1. The Canon Pixma TS6220 Wireless All-in-One printer
2. The installation setup CD
3. Standard ink cartridges/ ink tanks
4. The Power cord
5. The paper stack sample pack 4" x 6" (3 sheets)
6. Take out the other additional accessories from the box and place them aside.
7. Take the printer's body and make sure to remove all the existing paper materialsthat are present around the printer.
8. Place the printer in a secure location.
9. Place it on a steady surface.
10. Take out the power cord and connect the main end of the cord to the power source and the other end of the cable to the rear end of the printer.
11. Pull out the paper tray from the bottom of the printer and make sure to remove any protective tapes on the printer.
12. Install the papers in the paper tray;the printer supports the A4, A5, and B5 paper sizes.
13. You can load the additional documents at the rear tray of the printer, located right above the document feeder.
14. Align the edges of the paper and pull out the fold-back paper support on the rear paper tray.
15. Just below the paper tray, you will see a feed slot cover.
16. Pull out the feed slot cover, and you will see the paper guides.
17. Move the paper guides to either end before installing the papers.
18. Once the documents are appropriately aligned, move the paper guides to the edges of the paper to hold it tight.
19. Use the following steps we can execute the Canon Pixma Ts6220 Setup.

19. Do not keep the papers tight, as it may lead to paper jams. 
20. Place the feed slot cover back into the slot to close the rear paper tray.
21. Proceed to the next stepof installing the ink cartridges to the Canon Pixma printer.
22. Open the scanning unit that is located on top of the printer, you will see five ink tank slots.
23. Remove the packaging material from each ink cartridge cover.
24. Hold the ink tank by the edges, and do not touch the other part of the ink tank.
25. Open the orange protective cap from each of the ink cartridges and place the caps aside.
26. Gently place the ink tanks in the respective slots, push it inside until you hear the cartridge click in the slot.
27. Once you finish installing the ink tanks in the printer, close the scanning unit/cover.
28. The initial setup is now complete, turn on the printer by switching on the power source and pressing the power button on it.
29. Follow these steps we can execute the Canon Pixma Ts6220 Setup.

CANON PIXMA TS6220 PRINTER DRIVER INSTALLATION

1. Place the installation CD in the CD drive that came along with the Canon Pixma TS6220 printer.
2. Double-click on the My Computer or the This PC icon on the desktop.
3. Click on the CD drive from the page.
4. The contents of the CD will now be seen on the computer.
5. Navigate through the contents and click the exe file to proceed with the installation.
6. The PCL setup wizard will now open, click the Next button.
7. The license agreement page will now open. Click Yes to agree to the terms & conditions.
8. The installerwill now prompt you to select one of the three options:
9. Manual Setup
10. Wireless Setup
11. USB connection
12. Click the Wireless setup option and click the Next 
13. The Setup Wizard will now open two checkboxes, click the first checkbox PCL Printer driver and select the Add Printers radio button and click the Next
14. The setup wizard will now display a list of Canon printers in the Window, scrollto the Canon Pixma TS6220 printer and click the Add button and then the Next
15. Select the printer port from the drop-down list and click the Add port 
16. The printer driver setup page will now open, showing you the selections you have made on the page.
17. Click the Next button and click Start.
18. The driver will be installed successfully on the computer.
19. By utilizing these steps we can execute the Canon Pixma Ts6220 Setup.

CANON PIXMA TS6220 WIRELESS SETUP

You can set up the wireless connection for the Canon Pixma printer TS6220 while performing the driver installation.

1. Double-click on the downloaded driver file from the browser or insert the installation CD in the CD drive of the computer.
2. The Canon Pixma setup wizard will now open, click the Next button.
3. The license agreement page will now open, click the Agreebutton to the terms & conditions.
4. Click the Agree button for using the services related to the Canon product.
5. Select one of the three optionswhen prompted:
6. Manual Setup
7. Wireless Setup
8. USB connection
9. Click the Wireless setup option and click the Next 
10. Perform the connection referring to the image depicted in the setup window, click the Yes button.
11. The initialization will now start and will show the loading prompt on the screen.
12. Once the Wireless connection is set up for the Canon Pixma TS6220 printer, you will see a green tick mark near the image seen on the Setup wizard.
13. You can try to connect your printer and smartphone or any other device connected to the same network to check if the setup was completed successfully.
14. Perform these steps we can execute the Canon Pixma Ts6220 Setup.

Manual Printing:

1. Choose the required document you want to print and open the Printer driver setup window.
2. Click the Page Setup tab in the printer driver setup window.Click the checkbox for Duplex Printing and deselect the checkbox for automatic
3. Select a page layout;you can select Normal, borderless, fit to page, and scale from the list.
4. Select the number of copies by clicking the up and down arrow in the field.
5. Set the margin width if required, and click the OK
6. Complete the page setup.
7. When the printer starts printing, the printer will print on one side of the street. After the side is printed, you can reload the paper according to the instructions on the control panel.
8. Click Start Printing button to resume the double-sided printing.

Automatic Printing:

1. Choose the required document you want to print and open the Printer driver setup window.
2. Click the Page Setup tab in the printer driver setup window.Click the checkbox for Duplex Printing and Click the checkbox for automatic printing, to perform this action.
3. Select an appropriate page layout from the set of options provided.
4. Select one of the following options from the print area setup.
5. Click Use Normal size printing radio button and click OK.
6. Set the margin width and complete the setup by clicking OK.
7. The printer will now automatically print on both the sides of the paper according to the configured settings.
8. By using these steps we can execute the Canon Pixma Ts6220 Setup.

HOW TO SCAN WITH CANON PIXMA TS6220

1. You can scan from the Canon Pixma TS6220 using the IJ Scan Utility window.
2. You can see the options, Auto, document, photo, custom, OCR, Stitch, ScanGear, PDF editor.
3. Make sure the printer is turned on.
4. Place the documentto be scanned on the scanner feed and make sure it is appropriately aligned to the edges of the scanner glass.
5. Launch the IJ Scan utility.
6. Click the Auto option from the utility window.
7. The document will be scanned to the computer, and you can view the scanned document from the saved folder list.

CANON PIXMA TS6220 TROUBLESHOOTING

An unresponsive printer can cause you a lot of trouble, and this a common issue faced by most users. You may see the message Printer is not responding, or printer is not printing errors when you are trying to print a document from your computer.

1. The error indicates that the printer driver might be configured in the wrong port.
2. Launch the Run command by shortcut key- Windows Key + R key.
3. When the run command opens, enter the following command exe/name Microsoft. Troubleshooting and press the OK button.
4. Click the printer and select the troubleshooter option.
5. The troubleshooter will detect the problem related to the printing.
6. The troubleshooter window will ask you to follow the repair strategy.
7. Click the Apply button to fix the option and check to see if the error is resolved.
8. Restart the computer once and try performing a scanning or a printing option to see if the printer works properly.
9. Proceed the following steps we can execute the Canon Pixma Ts6220 Setup.

CANON PIXMA TS6220 OFFLINE

Method 1:

Method 2:

1. Launch the Run command by pressing the Windows key + R.
2. When the Run command window opens, type control printers and hit the Enter button.
3. Click the printer drop-down menu, check to see if you find the option Use Printer Offline.
4. Right-click on the printer option and select the option Online.

CANON PIXMA TS6220 PAPER JAM

When a paper is jammed during automatic duplex printing, you will see an error on the computer display screen while attempting to print.

The list of paper jam errors specifying a particular jammed location in the Canon Pixma TS6220 printer are:

1. 1300- the paper is jammed when feeding the paper from the rear paper tray.
2. 1303- the paper is jammed when feeding the paper from the cassette tray.
3. 1304- the paper is jammed while performing duplex printing.
4. 1313- the paper is jammed when the printer pulled in the printed paper.

Solution:

1. In such cases, hold the paper and pull out the jammed paper from the output slot gently so the document won't tear.
2. Now,you can reload the paper and press the Black or Color button in the control panel of the printer.
3. Remove the printer from the power source and turn it off.
4. Push the open lever and open the transport unit to pull out the jammed paper.
5. Close the document unit after removing the jammed paper.
6. Now,you can turn on the Canon TS6220 printer and then reload the paperback to the paper tray.

CANON PIXMA TS6220 RESET

1. Turn on the Canon Pixma TS6220 printer.
2. Navigate to the Settings option on the printer control panel. (Gear icon)
3. Select the following options: Device settings > Reset Settings
4. The Reset settings will show you four set of options:
5. By following steps we can execute the Canon Pixma Ts6220 Setup.

Web service setup only:

The printer’s web service settings will be set to default. 

LAN settings only:

To restore the default LAN settings.

Settings only:

To reset the paper size and media type settings to defaults.

Reset All:

It will reset all the printer settings to factory defaults and will erase the administrative password given by the Network device setup utility.

Choose an option depending on the issue you are facing.