Canon Pixma IP2702 Setup Guidance

Open the Canon Pixma IP2702 printer carton by removing the wrappers around it.
Prefer a flat surface to keep the Canon printer.
Peel off the orange-colored tapes on the printer.
Plug the power cable of the Canon Pixma IP2702 printer to an electrical wall outlet directly.
Switch on the Canon Pixma IP2702 setup by using its power button.
Lift the door at the top of the printer.
Wait until the cartridge holder slides and settles at its place.
Unpack the FINE ink cartridges provided in the printer box.
Insert the cartridges into the respective holders of the Canon Pixma IP2702 printer.
Open the access covers of the ink cartridges.
Insert the cartridges into the corresponding slots of the printer.
Close the access covers and door at the top of the Canon Pixma IP2702 printer.
Raise the paper tray at the top of the printer.
Slide out the guides and keep a stack of sheets in the tray.
Fix the sheets by adjusting the guides.
Launch the printer software to complete "Canon Pixma IP2702 printer setup".

Canon Pixma IP2702 Manual Download

Canon Pixma IP2702 Driver Installation Guidance

You can install the software for the Canon Pixma IP 2702 setup once you download it.
Open the driver file and follow the guidelines to install the software.

How to Change Ink Cartridge in Canon Pixma IP2702?

To change the ink cartridge of the Canon Pixma IP2702 setup, make sure that the printer is powered on.

Raise the cover at the front of the printer.

Now the holder of the FINE ink cartridge slides to its replacement process.

"Open" the locking cover of the ink cartridge.

"Locate" the FINE cartridge which you need to replace and take it out.

Take a "new cartridge" and unpack it.

Never forget to remove the orange-colored protective tapes on the cartridges.

Insert the FINE cartridge into the respective holder.

Note: The color cartridge should be placed into the slot at the left and black cartridge at the right.

Close the locking cover after fixing the cartridge.
Make sure that the cover is closed correctly.
Close the access cover at the front to complete the ink cartridge replacement process.

Steps: Canon Pixma IP2702 Wireless Setup

Ensure that the Canon Pixma IP2702 printer is turned on.
Hold the Wi-Fi key at the front of the printer for a while.
Tap the WPS button on your router within a few seconds.
Wait until the Canon Pixma IP2702 setup gets connected to the network of the router.
The Wi-Fi lamp on the printer indicates if the wireless connection is set up successfully.

How to Print Envelopes in Canon Pixma IP2702?

Raise the paper support of the Canon Pixma IP2702 printer.
Open the paper guides by sliding them.
Load your envelopes for printing in the center of the rear tray with the printable side facing you.
You load up to 5 envelopes in the tray.
Align the envelopes by adjusting the paper guides.
Open the Canon Pixma IP2702 printer software on your computer.
Configure the print settings for printing envelopes.
end the print job to your Canon Pixma IP2702 setup to print the envelopes.

Canon Pixma IP2702 Scanner Driver Install

There is not separate scanner software is designed for the Canon IP2702 setup. You can utilize the full featured software to perform the scan operation oft your printer.

Canon Pixma IP2702 Setup Troubleshooting Guidance

Fix any problems with the Canon Pixma IP2702 printer by availing assistance from our well-qualified technical experts. Following topics includes solutions to fix some common issues that arise with the Canon Pixma IP2702 printer.

How to Reset Canon Pixma IP2702 Printer?

There are two ways to reset the printer. One is by performing a hard reset on the printer, and the other method is using the appropriate options on the printer’s control panel.
Refer to the following steps to perform a hard reset on the Canon Pixma IP2702 setup.
Power on your Canon Pixma printer if it is switched off previously.
Once the printer powers on, disconnect its power cable.
Wait for a few minutes and connect the cable back to the printer and electrical outlet directly.
Now the printer turns on and resets to its default settings.

Resolved: Canon Pixma IP2702 won't Print

Ensure that the ink cartridges of the Canon Pixma IP2702 printer are inserted into the respective slots properly.
Make sure that the paper tray of the machine is loaded with compatible sheets.
Examine the connection between your Canon Pixma IP2702 printer and computer.
Reconnect the devices.
Reinstall the ink cartridges of the Canon Pixma IP2702 setup.

Solved: Canon Pixma IP2702 Error Code 5b00

Switch of the Canon Pixma IP2702 setup if it is powered off previously.
Hold the Resume key for a few minutes.
Press the Power button and release the Resume button.
Tap the Resume button for 4 times and tap the Power key.
Press the Power button.
Restart your printer and try to fix the 5B00 error.

Canon Pixma IP2702 Printer 5b00 Error Code Solution